How We Repair Your Maytag Commercial Washer
Washing machines fill, agitate or tumble, drain and spin using valves, a pump, a drive motor and suspension, all managed by a control board.
Maytag Commercial Washer models often use model-specific control boards, sensors and diagnostic modes. We look up your exact model number so the right part goes in the first time.
Common Commercial Washer Problems We Fix
Bad smell
Mildew in the door gasket, drain filter or detergent drawer.
Will not drain or spin
A clogged drain pump filter, a kinked drain hose, a failed drain pump or a lid or door lock that is not engaging.
Leaking
A worn door boot seal on front-loaders, a loose or cracked hose, or a failing tub seal or pump.
Shaking or walking during spin
An unbalanced load, worn shock absorbers or suspension springs, or a unit that is not level.
Will not start
A door lock fault, a control board problem or a failed lid switch.
Loud grinding or roaring
Worn tub bearings, usually on front-load machines.
Quick Checks Before You Call
These are safe for most owners and sometimes solve the problem without a visit:
- Clean the drain pump filter (front-loaders usually have a small door at the bottom).
- Make sure both water valves are open and hoses are not kinked.
- Redistribute heavy loads and check the machine is level.
- Write down any error code.
Still not working? Call (844) 442-1500 or try our troubleshooting wizard.
Our 5-Step Repair Process
- Call or book onlineTell us what your Maytag commercial washer is doing and when it started. We schedule the first available visit, with priority for equipment that is stopping your business.
- DiagnosisThe technician checks power, controls and the parts most likely to fail, using the model's service data and test modes.
- Upfront quoteYou get the cause, the repair and the price before any work starts. If repair does not make sense, we tell you.
- RepairWe install original or equivalent parts matched to your model and clean up when we are done.
- Test and warrantyWe run the appliance through a full cycle to confirm the fix. The repair is covered by our 90-day parts and labor warranty.
Parts We Replace Most Often
- Drain pump
- Door lock or lid switch
- Door boot seal
- Water inlet valve
- Shock absorbers and springs
- Drive belt and motor
- Tub bearings
- Control board
Cost and Lifespan
Most commercial washer repairs cost $150–$450 including parts and labor, and these appliances typically last 10–14 years. These are national estimates: your exact price comes after the diagnosis. Use the repair vs replace calculator to compare.
Keep It Running Longer
- Use HE detergent in the right amount
- Replace rubber fill hoses with braided ones every five years
- Leave the door open between loads
Commercial Washer Repair in Massachusetts
We repair commercial washers in 343 cities and towns across Massachusetts. Humid summers and long, cold winters in Massachusetts give homes across the state appliances a busy year, with heavy indoor use from fall to spring.
Frequently Asked Questions
How much does Maytag Commercial Washer Repair cost in Massachusetts?
Most commercial washer repairs fall between $150–$450 including parts and labor. The final price depends on the part that failed and your model. You get an exact quote after the diagnosis and before any work starts.
Can you repair my commercial washer today?
Same-day visits depend on technician availability in Massachusetts. Call (844) 442-1500 early in the day for the best chance of a same-day or next-day appointment.
Is the repair guaranteed?
Yes. Parts and labor are covered by our 90-day warranty. If the same problem comes back within that time, we return and fix it.
Do you work on all Maytag models?
We repair current and older Maytag models. Some discontinued parts can be hard to find; if that is the case for your model, we tell you before you pay for a repair.
Should I repair or replace my commercial washer?
A commercial washer typically lasts about 10 to 14 years. If yours is well inside that range and the repair costs less than half the price of a new one, repairing usually makes sense. Near the end of its life, or when the repair costs more than half of a replacement, replacing is often the better value. We give you an honest opinion either way.